Call our sales team
ERARD PRO TiLTiT 400 — an ultra-slim steel wall mount with up to 25° of downward tilt, for screens 30 to 65 inches up to 30 kg, with a minimum wall clearance of 30 mm. Supplied pre-assembled.
One order code, 30 to 65 inches
Load rating 30 kg
VESA 200 × 100 to 400 × 400
Tilt +0° / −25°, no swivel
Wall clearance from 30 mm
10 year warranty
Order code | Model | When to choose it |
|---|---|---|
044240 | TiLTiT 400 (this product) | screens 30 to 65 inches up to 30 kg placed above eye level, where the panel should stay close to the wall |
The family has a single order code in our offer, so where it sits in the range matters more than picking a variant. Against the fixed FiXiT 400, TiLTiT 400 adds downward tilt, against TWiSTiT 400 it has neither swivel nor extension from the wall. The 30 kg load rating and the 400 × 400 maximum pattern are the same on both tilting models.
Key features
Tilt of +0° / −25°, that is up to 25 degrees of downward tilt for the screen
Minimum wall clearance of 30 mm, an ultra-slim build even with a tilt mechanism
Load rating 30 kg for screens 30 to 65 inches, that is 76 cm to 165 cm
VESA pattern range from 200 × 100 to 400 × 400 including the rectangular combinations
Steel construction with epoxy paint, in a white and a black finish
Supplied pre-assembled, the installation time is 15 minutes
Approved for solid masonry as well as hollow plasterboard walls
Compatible with LCD and OLED screens with flat backs, maximum screen thickness 50 mm
Description
TiLTiT 400 addresses one specific situation, the screen hangs higher than eye level and the viewer looks up at it. That is the case in a reception, a lobby, a training room with a screen above an interactive whiteboard and in every installation where furniture or a desk left no room lower down. In such a position, tilting down by up to 25° noticeably improves legibility and suppresses reflections from ceiling lights.
In construction the model follows the same philosophy as the fixed FiXiT range, the screen as close to the wall as possible. A minimum clearance of 30 mm is little for a mount with tilt and it is the main reason TiLTiT is chosen over ordinary tilting mounts. The steel construction, the epoxy paint and the white and black finishes match the rest of the professional ERARD PRO range.
The family has a single item in our price list, so the choice is not made within the range but between ranges. If the screen is not to be tilted, FiXiT 400 is cheaper and slimmer. If the screen also has to swivel or move away from the wall, TWiSTiT 400 with the same 30 kg load rating belongs in the quote. The load rating and the 400 × 400 maximum VESA pattern of TiLTiT 400 match what our price list states, there is no discrepancy here.
Strengths and limits
Strengths
Up to 25° of downward tilt at a minimum clearance of 30 mm, which ordinary tilting mounts do not offer
Supplied pre-assembled, installation is a quarter of an hour of work
A wide pattern range from 200 × 100 to 400 × 400 covers the rectangular patterns too
Approved for solid and hollow walls alike, so it goes onto a plasterboard partition as well
Limits and what to tell the customer
The model has no swivel. The screen only tilts down, it does not turn to the side. For corner installations and for a screen watched from several directions, TWiSTiT 400 belongs in the quote.
The maximum screen thickness is 50 mm. On panels with a deep rear module, typically interactive displays and models with an integrated codec, the thickness has to be checked in advance.
Compatibility is declared for screens with flat backs. Curved or irregular backs call for separate adaptation.
Whether an integrated spirit level and an anti-drop safety catch are included, what the fixing hardware in the box consists of and what the wall clearance is at full tilt, we confirm at order.
⚑ atlantis note
Installation height decides the tilt
When the centre of the screen is above the eye level of a seated person, tilting down noticeably improves legibility and suppresses reflections from ceiling lights. If the screen hangs at eye level, you do not need tilt and the fixed FiXiT 400 is both slimmer and cheaper. So settle the height of the screen centre before the model of the mount.
Check the screen thickness at the very start
The ceiling is 50 mm and it is the parameter a quote most often falls on. Interactive panels and screens with an integrated codec or a built-in computer module tend to be deeper. This figure is always in the screen datasheet, it is enough to look at it before the quote goes out.
The cabling has to allow for movement
The 30 mm clearance applies in the parked position, at full tilt the space behind the screen changes. So run the cables with slack for the whole tilt range and place the wall penetration so that nothing pulls or kinks the cable when the screen tilts.
Which installation
Model coverage | screens 30 to 65 inches, load rating 30 kg, maximum screen thickness 50 mm |
|---|---|
Wall type | solid masonry wall as well as hollow plasterboard partition, anchors to suit the construction |
Position in the portfolio | an ultra-slim tilting wall mount for indoor professional installations |
Suitable
A screen above a reception desk, in a lobby and above an entrance, a training room with a screen above an interactive whiteboard, a signage panel placed higher because of furniture. Anywhere the screen is watched from below and should still stay close to the wall.
Verify
The weight, VESA pattern and thickness of the specific screen from its datasheet. The height of the screen centre and the tilt angle that follows from it. The wall construction and any need for load-bearing preparation. Where power and data will run.
Consider another model
A screen heavier than 30 kg or larger than 65 inches, a need to swivel sideways and extend from the wall, a screen with a curved back, an installation with no drilling into the wall, a screen at eye level with no need for tilt.
The “Suitable” field follows from the technical parameters of the model, the “Verify” and “Consider another model” fields from the practice of the atlantis team.
Load, VESA and screens
Code | Model | Load | Max. VESA | Diagonal | Clearance | Tilt |
|---|---|---|---|---|---|---|
044240 | TiLTiT 400 | 30 kg | 400 × 400 | 30" to 65" | from 30 mm | +0° / −25° |
The mount measures 460 mm wide, 420 mm high and 35 mm deep, and weighs 3.75 kg. The maximum screen thickness is 50 mm and the smallest supported pattern is 200 × 100. The construction is steel with epoxy paint in a white and a black finish, installation takes 15 minutes and the mount is supplied pre-assembled.
In the box
In the box
The pre-assembled TiLTiT 400 mount in steel with epoxy paint
The tilt mechanism with a range of +0° / −25°
Not included
The screen
Anti-theft cable for publicly accessible spaces, ref. 012395
An adapter plate for a VESA pattern outside the supported range
The exact fixing hardware in the box, that is the count and type of screws, wall plugs and spacers, we confirm at order. We also confirm whether an integrated spirit level and an anti-drop safety catch are part of the delivery. Wall fixings are always chosen to suit the wall construction and the screen weight.
Order with it
Adapter plate VESA 75 × 200100742
Turns a mount with a VESA 75 or 100 pattern into 200 × 200, 200 × 100 or 100 × 200.
Adapter plate VESA 75 × 400100740
Mounts on a VESA 75, 100 or 200 pattern and extends it up to 400 × 400.
Anti-theft cable012395
For publicly accessible spaces.
Wall anchorsper wall
Chosen to suit the wall construction and the screen weight, plasterboard needs load-bearing preparation.
Where the range sits
Range | Version | Load | Purpose |
|---|---|---|---|
CLIFF | fixed and tilting | 15 kg and 30 kg | general fixed mounting, 15 to 85 inches |
FiXiT | fixed, ultra-slim | 50 kg to 70 kg | a heavier screen close to the wall with minimal clearance |
TiLTiT ◂ this range | ultra-slim, tilting | 30 kg | a screen above eye level that should stay at the wall |
TWiSTiT | ultra-slim, tilting and swivelling | 30 kg | the screen has to swivel or move away from the wall |
EXO and EXOSTAND | swivel arm, column | 25 kg and 35 kg | a design arm or a floor-to-wall column |
STANDiT | column leaning on the wall | 30 kg to 50 kg | an installation with no drilling into the wall |
What to verify before ordering and installing
Screen weight: from the screen datasheet, not from the diagonal, the ceiling is 30 kg
Screen thickness: the maximum is 50 mm, on panels with a deep rear module it is the first thing to check
VESA pattern: the specific screen model, the supported range is 200 × 100 to 400 × 400
Installation height: a screen centre above eye level is the reason for tilt, otherwise a fixed mount is enough
Wall construction: masonry, concrete or plasterboard and the anchors that follow
Load-bearing preparation: on plasterboard and with a screen approaching 30 kg it is settled at the building stage
Cabling: slack for the whole tilt range and a wall penetration behind the screen
Back of the screen: compatibility is declared for flat backs, curved ones call for adaptation
The atlantis team helps with every point. From matching the mount to the specific screen through building readiness and cabling to installation, commissioning and handover of the documentation.
Installation design and services
The weakest link sets the load rating of the assembly: in a stand plus screen mount plus shelf assembly, the lowest of the stated load ratings always applies. Check the screen weight in its own datasheet, not from the diagonal.
Check VESA before ordering: the stated range is the maximum pattern, not a guarantee that the screen fits. On large formats and on screens with curved or irregular backs, verify both the pattern and the thickness in advance.
The wall type decides the fixing hardware: plasterboard, masonry and concrete each need different anchors. On part of the range the wall screw set is not in the box and the fixing hardware is chosen on site to suit the wall.
Cabling and service access belong in the design, not on the installation day: cable routing inside the column, the wall penetration and access to the back of the screen have to be in the room layout before anyone drills.
atlantis services for partners
atlantis is a direct importer and distributor, and we supply through a network of specialist partners. The services below are therefore offered to the partner, not to the end customer. The partner sets the scope. On one project we are only the source of the parts and a consultation, on another we design the whole run and oversee the work, on a third we take on the installation in full.
Choosing the kit by camera and distance: we pick the kit from the camera or codec the customer already has, how far it sits from the equipment and which interface is used, that is HDMI, USB or fibre. We also say what to do about a device that is not on the compatibility list.
Route design and building readiness: we go through the cable run with the partner, the category and length of the cabling, the number and position of the boxes, the wall penetration and the space in the rack. On in-wall mounts the opening size and cavity depth are what matters, and we settle those before the order, not on site.
Completing the order: we match the kit with the right cables, power supply and mount, because that is exactly where jobs are left unfinished. We check that the pieces fit each other by connector and by length, and that nothing the partner needs on day one is missing from the delivery.
Installation and commissioning: we handle the professional installation in full, or support the partner's own team where needed. Once it is wired we test the link at full distance, that is picture, camera control and power, before the ceiling is closed.
Integration with the customer's environment: we advise on connecting to the codec, to the control system and to third-party software and hardware, and on how the kit behaves when the camera is swapped for a different model.
Service, spare parts and warranty: our certified team in Czech, available to the partner throughout the equipment's life. We keep track of the replacement modules and parts by range and handle a warranty claim with the manufacturer on the partner's behalf.
Warranty
The ERARD PRO range is passive mechanics, so the warranty covers the structure, the welds, the moving parts and the finish. The warranty term is not the same across the brand and for a given item it is what is stated below.
Standard
10 years on the mechanics
This product carries a 10 year warranty, which ERARD PRO gives on most of its range. It covers the mechanics and the finish in indoor use.
10 years
Environment
Indoor use
The range is designed for indoor use. Outdoor installations, high humidity and aggressive environments are outside the scope of the warranty.
indoor
Take note
Installation per the manual
The warranty assumes installation per the manufacturer's manual and anchors suited to the wall construction. Exceeding the load rating or the VESA range is the most common reason a claim fails.
load and VESA
Frequently asked questions
What is the difference between TiLTiT 400 and FiXiT 400?
The tilt. 044240 tilts the screen down by up to 25° and holds it at least 30 mm off the wall. FiXiT 400 has no tilt, holds the screen 16 mm off the wall and carries 60 kg against the 30 kg of TiLTiT. If the screen hangs at eye level and is not meant to move, FiXiT is the right choice.
What is the difference between TiLTiT 400 and TWiSTiT 400?
Swivel and extension. Both models have the same 30 kg load rating, the same 30 to 65 inch span of diagonals and the same 400 × 400 maximum pattern. TWiSTiT 400 additionally swivels the screen by ±90° and brings it up to 710 mm in front of the wall, at the price of a larger minimum clearance of 58 mm and a markedly heavier mount.
How large is the tilt and does the screen tilt upwards?
The range is +0° / −25°, that is downward tilt only, up to 25 degrees. The screen cannot be tilted upwards and there would be no point, the tilt addresses the situation where the screen hangs above eye level and the viewer looks up at it.
How thick a screen fits on the mount?
The maximum screen thickness is 50 mm. On ordinary professional panels that is not an issue, on interactive displays and on models with an integrated codec or a built-in computer module it is. The thickness is in the screen datasheet and it belongs among the first things to check.
Can the mount go on plasterboard?
Yes, the model is approved for solid and hollow walls alike. The anchors do have to suit the wall construction and the screen weight. With a screen approaching 30 kg on a plasterboard partition, load-bearing preparation is needed, that is a reinforcement or a stud at the fixing point, and it is settled at the building stage.
How many people are needed for the installation?
The mount is supplied pre-assembled and fixing it to the wall takes roughly 15 minutes. Hanging a screen approaching 30 kg is a two-person job though, even if one person manages the mount itself.
- Manufacturer
- Erard
- Weight
- 3.9 kg
No attachments available.
Not sure what to choose?
We're happy to help you choose!
Every business day from 8:00 to 17:00