Axeos X-PRESS single - for 1 monitor 40" - 70"

Axeos X-PRESS is a light assembly that leans against a wall or is anchored to it, weighs 23 kg and carries a 40 to 75-inch screen up to 45 kg. It is the quickest way to put a screen against a wall without drilling into load bearing structure.

Key features

• Screen 40 to 75", VESA 200 x 200 mm to 600 x 400 mm.

• Load 45 kg, and 35 kg when merely leaning on the wall, above 35 kg two anchor points are required.

• Maximum screen depth 60 mm.

• Screen axis 1360 to 1580 mm, camera shelf 865 to 1132 mm.

• A notch for the skirting board 239 mm high and 52 mm deep.

• Steel structure in a white finish, weight 23 kg, a patented design.

Description

The lightest assembly in the range

At 23 kg the X-PRESS fits in a car and one person can put it up without lifting gear. On the other ranges the weight runs from 30 to 160 kg.

Leaning or anchoring, by the weight of the screen

Up to 35 kg leaning against the wall is enough, above 35 kg two anchor points are required. The limit is 45 kg, so the X-PRESS is meant for screens up to 75 inches, not for heavy large format panels.

A camera shelf with a wide range

The shelf adjusts over 865 to 1132 mm, a range of 267 mm. The camera on the AX055-05 shelf may weigh at most 1.8 kg, which covers usual USB cameras and video bars within that weight.

Strengths and limits

Where it fits

Huddle rooms and small meeting rooms

A 55 to 65-inch screen with a USB camera on the shelf is the typical configuration for a room of up to six people.

Temporary installations and loans

The 23 kg weight and installation without lifting gear make the X-PRESS the answer for demonstrations, loan units and off site training.

Rooms where drilling is not allowed

Up to 35 kg the assembly simply leans against the wall. Above that weight two anchor points are needed.

Order variants

The standard finish is white steel. For the codes X-PRESS-DS and CARTER_XPRESS we confirm what is supplied with your order.

Technical specifications

In the box

Do not forget to order

Variants and products in the range

What to check before ordering and installing

1. Screen weight: up to 35 kg leaning is enough, above 35 kg two anchor points are required

2. Screen depth: 60 mm at most, panels with a deep frame will not work

3. VESA: up to 600 x 400 mm

4. Camera: the shelf carries 1.8 kg, check the weight of the video bar

5. Skirting board: a notch of 239 x 52 mm

6. Wall: for anchoring, check the material and whether drilling is allowed

7. Finish: white as standard, black as an option

The atlantis team will help with every point.

Management and services

• No software, no management: Axeos stands, mounts and furniture are mechanical structures with no firmware and no central management. What is managed is the technology mounted on them.

• Custom finishes: Axeos manufactures in France and supplies most ranges in other finishes, with custom text or with a modified plate. We confirm the lead time and price of such a change with your order.

atlantis services for partners

atlantis is a direct importer and distributor, and we supply through a network of specialist partners. The services below are therefore offered to the partner, not to the end customer. The partner sets the scope. On one project we are only the source of the parts and a consultation, on another we design the whole run and oversee the work, on a third we take on the installation in full.

• Choosing the kit by camera and distance: we pick the kit from the camera or codec the customer already has, how far it sits from the equipment and which interface is used, that is HDMI, USB or fibre. We also say what to do about a device that is not on the compatibility list.

• Route design and building readiness: we go through the cable run with the partner, the category and length of the cabling, the number and position of the boxes, the wall penetration and the space in the rack. On in-wall mounts the opening size and cavity depth are what matters, and we settle those before the order, not on site.

• Completing the order: we match the kit with the right cables, power supply and mount, because that is exactly where jobs are left unfinished. We check that the pieces fit each other by connector and by length, and that nothing the partner needs on day one is missing from the delivery.

• Installation and commissioning: we handle the professional installation in full, or support the partner's own team where needed. Once it is wired we test the link at full distance, that is picture, camera control and power, before the ceiling is closed.

• Integration with the customer's environment: we advise on connecting to the codec, to the control system and to third-party software and hardware, and on how the kit behaves when the camera is swapped for a different model.

• Service, spare parts and warranty: our certified team in Czech, available to the partner throughout the equipment's life. We keep track of the replacement modules and parts by range and handle a warranty claim with the manufacturer on the partner's behalf.

Warranty

The manufacturer warranty on this product is 10 years.

Frequently asked questions